DLink Connected Home myDlink Control4 Driver

Easily integrate your mydlink Wi-Fi connected smart home devices such as the Water Sensor, Smart Plugs, Siren and motion sensor into the Control4 home automation platform.

MSRP: $149
Login to view pricing

Now the popular and inexpensive Wi-Fi enabled D-Link smart home products can augment your Control4 system. Our mydlink Control4 driver pack includes support the following devices. Add as many of these to your project and use the same license code to integrate them all.

Wi-Fi Water Sensor
DCH-S160

  • Control4 event will fire upon water detection
  • Ability to bind a generic water sensor for on-screen UI display
  • Watchdog variable to detect if it falls off the wireless network
  • Water Sensor Cable total cable length of 4.8 feet
  • Extension cable: 3.2 feet (RJ11 cable)
  • Water sensing cable: 1.6 feet
  • One alarm sound built-in to device
  • Alarm Volume - 70dB
  • Alarm will sound and LED will blink red when water is detected
  • 802.11n/g wireless Frequency Range
  • 2.4GHz to 2.4835GHz Maximum Operating Range
  • Two internal antennas
  • FCC and UL rated

Wi-Fi Smart Plug
DSP-W215

  • Full v2 Light proxy support
  • Relay binding support
  • Supports energy monitoring with use statistics
  • Temperature feedback
  • Watchdog variable to detect if it falls off the wireless network
  • 802.11n
  • Power Input: 100 to 125 V AC
  • Power Capacity: Up to 1800W / 15Amps
  • FCC and UL rated

Wi-Fi Siren
DCH-S220

  • Trigger different sounds from Control4
  • 6 different built-in sounds:
    • Emergency
    • Fire
    • Ambulance
    • Police
    • Door Chime
    • Arm/Disarm
  • Selectable volume - 100 / 90 / 80 dB
  • Watchdog variable to detect if it falls off the wireless network
  • Sound alarm based on trigger from Control4 events
  • 802.11n/g wireless Frequency Range
  • 2.4GHz to 2.4835GHz Maximum Operating Range
  • Two internal antennas
  • FCC and UL rated

Wi-Fi Smart Plug
DSP-W110

  • Full v2 Light proxy support
  • Relay binding support
  • Watchdog variable to detect if it falls off the wireless network
  • 802.11n
  • Power Input: 100 to 125 V AC
  • Power Capacity: Up to 1800W / 15Amps
  • FCC and UL rated

Wi-Fi Motion Sensor
DCH-S150

  • Trigger events in Control4 based upon motion detection
  • Watchdog variable to detect if it falls off the wireless network
  • Connection for generic motion sensor for UI display
  • NOTE: Only detects motion every 10 minutes; should not be used if you need instant motion detection
  • PIR Motion Sensor
  • Sensor Distance 26-feet
  • Wireless 802.11 b/g/n
  • Two internal antennas
  • FCC and UL rated

Driver License:  Site (one required per project)

v1.5
 - Adjusted the way that the light and relay proxies are notified of state changes.

v1.4
 - Added handling of advanced lighting scenes.
 - Added handling of proxy messages from button panels.

v1.3
 - Adjusted retry timers. If an HTTP request fails, retry once a minute for 15m, then once an hour for 12h, then every 12 hours indefinitely.
 - Driver now attempts to sign in on driver init.

v1.2
 - Fixed a bug where devices without any device type were causing the "List Associated Device" button to fail.

v1.1
 - Watchdog variable added in case unit goes offline
 - Fixed bindings on motion/water sensor


Please note that you must configure the device using the mydlink app first. 

 

-------------------------------------------------------------------------------------------
OVERVIEW
-------------------------------------------------------------------------------------------

This driver integrates the mydlink Wi-Fi Energy Monitoring Smart Plug into a Control4 system.

The driver polls every 5 minutes to obtain present Wattage and Temperature values from the plug.

First, enter a license key. Then enter your e-mail and password associated with your mydlink account. The remaining property fields should populate with relevant device info.

Obtain a Device ID after signing in by navigating to the "Actions" tab and pressing the "List Devices" button. The Device table will then print out in the Lua tab.

This device supports the Light V2 proxy as well as a relay connection.

To utilize the relay connection, add a relay binding and connect it under the Connections tab to control the device via relay.

-------------------------------------------------------------------------------------------
PROPERTIES
-------------------------------------------------------------------------------------------
License Key:
This is the license key purchased to activate the driver.

License Status:
This is the status of the license activation.

E-mail:
This is the E-Mail address associated with your mydlink account.

Password:
This is the password associated with your mydlink account.

Device ID:
Unique device identifier. To obtain this, sign in and then press the "List Devices" action button.

Type:
Class of the device. Populates after entering a valid Device ID.

Model:
Model number of the device. Populates after entering a valid Device ID.

MAC Address:
MAC address of the device. Populates after entering a valid Device ID.

Firmware Version:
Firmware version of the device. Populates after entering a valid Device ID.

Online Status:
Goes ONLINE when a successful web request is made to the device. Goes OFFLINE on communications error.

DEBUG MODE:
Enable/disable debug mode.

-------------------------------------------------------------------------------------------
OVERVIEW
-------------------------------------------------------------------------------------------

This driver integrates the mydlink Wi-Fi Smart Plug into a Control4 system. First, enter a license key. Then enter your e-mail and password associated with your mydlink account. The remaining property fields should populate with relevant device info.

Obtain a Device ID after signing in by navigating to the "Actions" tab and pressing the "List Devices" button. The Device table will then print out in the Lua tab.

This device supports the Light V2 proxy as well as a relay connection.

To utilize the relay connection, add a relay binding and connect it under the Connections tab to control the device via relay.

-------------------------------------------------------------------------------------------
PROPERTIES
-------------------------------------------------------------------------------------------
License Key:
This is the license key purchased to activate the driver.

License Status:
This is the status of the license activation.

E-mail:
This is the E-Mail address associated with your mydlink account.

Password:
This is the password associated with your mydlink account.

Device ID:
Unique device identifier. To obtain this, sign in and then press the "List Devices" action button.

Type:
Class of the device. Populates after entering a valid Device ID.

Model:
Model number of the device. Populates after entering a valid Device ID.

MAC Address:
MAC address of the device. Populates after entering a valid Device ID.

Firmware Version:
Firmware version of the device. Populates after entering a valid Device ID.

Online Status:
Goes ONLINE when a successful web request is made to the device. Goes OFFLINE on communications error.

DEBUG MODE:
Enable/disable debug mode.

-------------------------------------------------------------------------------------------
OVERVIEW
-------------------------------------------------------------------------------------------

This driver integrates the mydlink Wi-Fi Siren into a Control4 system.

The siren has customizable sound, volume, duration, and may be controlled with a relay.

First, enter a license key. Then enter your e-mail and password associated with your mydlink account. The remaining property fields should populate with relevant device info.

Obtain a Device ID after signing in by navigating to the "Actions" tab and pressing the "List Devices" button. The Device table will then print out in the Lua tab.

This device supports a relay connection. Add a relay binding and connect it under the Connections tab to control the device via relay.

-------------------------------------------------------------------------------------------
PROPERTIES
-------------------------------------------------------------------------------------------
License Key:
This is the license key purchased to activate the driver.

License Status:
This is the status of the license activation.

E-mail:
This is the E-Mail address associated with your mydlink account.

Password:
This is the password associated with your mydlink account.

Device ID:
Unique device identifier. To obtain this, sign in and then press the "List Devices" action button.

Sound:
The sound played by the siren during alarm.

Volume:
Alarm volume. Range 0-100.

Duration:
Alarm duration in seconds.

Type:
Class of the device. Populates after entering a valid Device ID.

Model:
Model number of the device. Populates after entering a valid Device ID.

MAC Address:
MAC address of the device. Populates after entering a valid Device ID.

Firmware Version:
Firmware version of the device. Populates after entering a valid Device ID.

Online Status:
Goes ONLINE when a successful web request is made to the device. Goes OFFLINE on communications error.

DEBUG MODE:
Enable/disable debug mode.

-------------------------------------------------------------------------------------------
OVERVIEW
-------------------------------------------------------------------------------------------

This driver integrates the mydlink Wi-Fi Motion Detector into a Control4 system.

The driver checks for motion detected events. If motion has been detected, a Control4 event is fired and the motion detected event list is cleared.

Motion detection may be turned ON/OFF from the driver property and the sensitivity is adjustable from the driver property.

First, enter a license key. Then enter your e-mail and password associated with your mydlink account. The remaining property fields should populate with relevant device info.

Obtain a Device ID after signing in by navigating to the "Actions" tab and pressing the "List Devices" button. The Device table will then print out in the Lua tab.

This device supports a Contact Sensor input connection to connect a Motion Detector.

-------------------------------------------------------------------------------------------
PROPERTIES
-------------------------------------------------------------------------------------------
License Key:
This is the license key purchased to activate the driver.

License Status:
This is the status of the license activation.

E-mail:
This is the E-Mail address associated with your mydlink account.

Password:
This is the password associated with your mydlink account.

Device ID:
Unique device identifier. To obtain this, sign in and then press the "List Devices" action button.

Motion Detection:
Enable or disable motion detection on the device.

Sensitivity:
Adjust the motion detection sensitivity of the device. Range 0-100.

Type:
Class of the device. Populates after entering a valid Device ID.

Model:
Model number of the device. Populates after entering a valid Device ID.

MAC Address:
MAC address of the device. Populates after entering a valid Device ID.

Firmware Version:
Firmware version of the device. Populates after entering a valid Device ID.

Online Status:
Goes ONLINE when a successful web request is made to the device. Goes OFFLINE on communications error.

DEBUG MODE:
Enable/disable debug mode.

-------------------------------------------------------------------------------------------
OVERVIEW
-------------------------------------------------------------------------------------------

This driver integrates the mydlink Wi-Fi Water Sensor into a Control4 system.

The driver checks for water detected events. If water has been detected, a Control4 event is fired and the water detected event list is cleared.

First, enter a license key. Then enter your e-mail and password associated with your mydlink account. The remaining property fields should populate with relevant device info.

Obtain a Device ID after signing in by navigating to the "Actions" tab and pressing the "List Devices" button. The Device table will then print out in the Lua tab.

This device supports a Contact Sensor input connection to connect a Water Sensor.

-------------------------------------------------------------------------------------------
PROPERTIES
-------------------------------------------------------------------------------------------
License Key:
This is the license key purchased to activate the driver.

License Status:
This is the status of the license activation.

E-mail:
This is the E-Mail address associated with your mydlink account.

Password:
This is the password associated with your mydlink account.

Device ID:
Unique device identifier. To obtain this, sign in and then press the "List Devices" action button.

Type:
Class of the device. Populates after entering a valid Device ID.

Model:
Model number of the device. Populates after entering a valid Device ID.

MAC Address:
MAC address of the device. Populates after entering a valid Device ID.

Firmware Version:
Firmware version of the device. Populates after entering a valid Device ID.

Online Status:
Goes ONLINE when a successful web request is made to the device. Goes OFFLINE on communications error.

DEBUG MODE:
Enable/disable debug mode.
-------------------------------------------------------------------------------------------